#VIMR QUIT UNEXPECTEDLY HOW TO#
#VIMR QUIT UNEXPECTEDLY DRIVER#
#VIMR QUIT UNEXPECTEDLY MANUAL#

For example, the PowerToysвЂ™ feature of Mute Video Conference is a reported culprit. Conflicting Applications: If a utility/service/ process on your system is hindering the application modules of the Zoom app, then it may crash.

#VIMR QUIT UNEXPECTEDLY DRIVER#

Outdated Zoom App: If the Zoom app is outdated, it may become incompatible with other OS components like the graphics driver and thus cause the screen sharing issue.

'Calibration','Internal Temp Model','Int Maximum Temp','6232','0. 'Calibration','Internal Temp Model','Int Minimum AD','0','-'

'Calibration','Internal Temp Model','Int base offset','6232','-' 'Calibration','Temperature','External4 Temp Offset','0','degC' 'Calibration','Temperature','External3 Temp Offset','0','degC' 'Calibration','Temperature','External2 Temp Offset','0','degC' 'Calibration','Temperature','External1 Temp Offset','0','degC' 'Calibration','Temperature','Internal Temp Offset','0','degC' 'Calibration','Current Offset','CC Auto Offset','0','-' 'Calibration','Current Offset','CC Auto Config','07','hex' 'Calibration','Current Offset','Board Offset','0','-' 'Calibration','Current Offset','Coulomb Counter Offset Samples','64','-' 'Calibration','Current Offset','CC Offset','0','-' * Field Order: Class name, Subclass name, Parameter name, Parameter Value, Display Units gg.csv.txt * Texas Instruments Data Flash File Any insight would be greatly appreciated. Not all registers are reset to a known state.ДЄfter starting Learn again, which won't start because of RDIS bit:ДЄt this point, I feel I've tried most combinations that make sense. I'm noticing inconsistent behavior after sending 'RESET'. In the hopes of figuring this out, I'm attempting to document exactly the steps that I've tried. I have not been able to switch those bits since the first time that I confirm I was able to. My recollection is that bits 1:2 in Operation Status A (CHG and DSG) correspond to the actual FET outputs. I was able to enable the FET in the past so I'm very confident that my hardware setup is correct. I've attempted to follow your instructions and I cannot even get DSG FET output to turn on to start the first step of discharging the battery. Maybe I'm missing some configuration on this step that is a chip wide FET enable?Д¤. I don't know enough about my batteries' limits to tune the settings much better than generic safe LiPo limits. All of the defaults I've found seem sane. I'm still unclear on which 'settings, protection and gauging parameters' are required to be set before learning.

#VIMR QUIT UNEXPECTEDLY MANUAL#

Does the learning cycle do software control of the CHG and DSG FET outputs? Some reading suggested you were supposed to use the manual CHG/DSG FET controls for the learning cycle. I'm assuming you're saying I should ensure the FET_EN bit is set (red box in bqStudio)Дў. It seems FET_EN button/command is really a 'toggle' for the FET_EN bit in 'Manufacturing Status'.

Unfortunately, this does not quite answer my questions and confusions.ДЎ. I've tried sending a 'Fuse Toggle' command via 0x001D manually but bqStudio reports communication errors (only for manual SMBus commands).

#VIMR QUIT UNEXPECTEDLY HOW TO#

It looks like the FUSE output is enabled and preventing DSG/CHG but I cannot figure out why or how to clear it. I've been able to enable them in the past with some combination of sending FET_EN, CHG_FET_TOGGLE, and DSG_FET_TOGGLE. Once the learning cycle claims to have started, the output FETs are not enabled. However finding where I can set that register in bqStudio has taken more time that I care to admit and I still struggle to find it on subsequent runs. To make matters even more confusing, the register locations given in the advanced view do not line up with anything that I can find in the reference manual.ДЇor instance, RDIS must be set to enable the learning cycle. The main annoyance is that bqStudio's names for registers do not always line up exactly with the names printed in the reference manual. Is there a 'learning cycle guide' available? We're finding it particularly difficult to get the learning cycle going. We're trying to get our bq40z60 up and running with bqStudio. Other Parts Discussed in Thread: BQ40Z60, BQSTUDIO, BQ40Z60EVM, BQ2947

Vimr quit unexpectedly